List of Wi-Fi configuration parameters

Last Updated : Apr 17, 2026 |
Prolog information
Metadata
Keywords:
Parameter Name
Default Value
Description
WIFISTAT
1
Specifies the network interface to be used for network connectivity.
Value operation:
  • 0: Phone connects to only Ethernet network.
  • 1: Phone connects to Ethernet network, unless manually switched to Wi-Fi
  • 2: Phone connects to the Wi-Fi network with the SSID defined in the 46xxsettings.txt parameter WLAN_ESSID
ENABLE_NETWORK_CONFIG_BY_USER
1
Enables network configuration to be modified by the user.
Value operation:
  • 0: Disabled
  • 1: Enabled
WLAN_ESSID
N/A
Specifies the wireless network to be used.
The name of the SSID ranges up to 32 characters.
WLAN_SECURITY
none
Specifies the security standard to be used for the wireless network.
Value operation:
  • none: No security standard is defined.
  • wep: WEP security standard is defined.
  • wpa2psk: WPA2 security standard with pre-shared key is defined.
  • wpapsk: WPA security standard with pre-shared key is defined.
  • wpa2e: WPA enterprise security standard is defined.
WEP_DEFAULT_KEY
N/A
Specifies the index of WEP default key.
Value operation:
  • 1
  • 2
  • 3
  • 4
WLAN_COUNTRY
US
Specifies the ISO country code representing the Wi-Fi regulatory domain.
WLAN_ENABLE_80211D
0
Enables the phone to configure its Wi-Fi regulatory domain to match the 802.11d.
Value operation:
  • 0: Disable
  • 1: Enable
WLAN_MAX_AUTH_FAIL_RETRIES
Specifies the number of times the phone will retry a secure connection upon receiving (possibly successive) auth failures.
The valid values range from 0 to 4.
WEP_KEY_LEN
128 bit
Specifies the length of the WEP key.
Value operation:
  • 40 bit
  • 64 bit
  • 128 bit
WLAN_PASSWORD
N/A
Specifies the pre-configured Wi-Fi network password. This parameter is applicable if the WIFISTAT is enabled and WLAN_SECURITY is wpa2psk, or WLAN_SECURITY is wpa2e, WLAN_WPA2E_EAP_METHOD is PEAP and WLAN_WPA2E_EAP_PHASE2 is MSCHAPV2.
The password must be from 8 to 63 characters. Note that the space and ASCII 0x20 are not supported.
WLAN_WPA2E_EAP_PHASE2
N/A
Specifies the pre-configured Wi-Fi network 802.1x phase 2 Method. This parameter is only applicable when WIFISTAT enables Wi-Fi and WLAN_SECURITY is wpa2e and WLAN_WPA2E_EAP_METHOD is PEAP.
Value operation:
  • none- No phase 2 authentication (Default, but not currently supported)
  • MSCHAPV2 : set to this value for forward compatibility
Note:
Avaya J129 IP Phone, Avaya J159 IP Phone, and Avaya J179 IP Phone support a pluggable Wi-Fi/BT module
WLAN_WPA2E_ANONYMOUS_IDENTITY
Null
Specifies the pre-configured Wi-Fi network 802.1x anonymous identity. This parameter is only applicable when WIFISTAT enables Wi-Fi and WLAN_SECURITY is wpa2e and WLAN_WPA2E_EAP_METHOD is PEAP and WLAN_WPA2E_EAP_PHASE2 is MSCHAPV2.
The value can contain 1 to 32 characters; Valid characters are: A-Z, a-z, 0-9, and the following: *.-!$%&'()+,:;/\=@~ The space character, ASCII 0x20, is NOT supported.
Note:
Avaya J129 IP Phone, Avaya J159 IP Phone, and Avaya J179 IP Phone support a pluggable Wi-Fi/BT module
WEP_KEY_1 to WEP_KEY_4
N/A
Specifies the name of the WEP key.
The name of the 40 bit key and 128 bit key are of 10 hex digits and 26 hex digits respectively.
WLAN_WPA2E_EAP_METHOD
PEAP
Specifies the pre-configured 802.1x EAP method. This parameter is applicable if WIFISTAT parameter is enabled and WLAN_SECURITY is set as wpa2e.
Value operation:
  • PEAP
  • TLS
WLAN_WPA2E_IDENTITY
N/A
Specifies the 802.1x name of pre-configured Wi-Fi network. This parameter is applicable if WIFISTAT parameter is enabled and WLAN_SECURITY is set as wpa2e.
The name must be from one to 32 characters.
Note that the space character and ASCII 0x20 are not supported.
WLAN_WPA2E_ANONYMOUS_IDENTITY
N/A
Specifies the 802.1x anonymous name of pre-configured Wi-Fi network. This parameter is applicable if WIFISTAT parameter is enabled, WLAN_WPA2E_EAP_METHOD is set to PEAP and WLAN_SECURITY is set as wpa2e.
The name must be from one to 32 characters.
Note that the space character and ASCII 0x20 are not supported.
WLAN_L2QAUD
6
Specifies the layer 2 priority value for audio frames generated by the telephone.
Valid value is from 0 to 7.
WLAN_DSCPAUD
46
Specifies the layer 3 Differentiated Services (DiffServ) Code Point for audio frames generated by the telephone.
Valid value is from 0 to 63.
WLAN_L2QSIG
3
Specifies the layer 3 Differentiated Services (DiffServ) Code Point for audio frames generated by the telephone.
Valid value is from 0 to 63.
WLAN_DSCPSIG
34
Specifies the layer 3 Differentiated Services (DiffServ) Code Point for signaling frames generated by the telephone.
Valid value is from 0 to 63.